DuxTel Systems (11)
Interface Cards and Adapters (14)
Mikrotik Systems-> (159)
Mimosa Wireless (5)
RouterBOARD (11)
Router Enclosures (11)
Power Supplies & PoE-> (29)
Antennas and Accessories-> (106)
Mikrotik RouterOS (6)
Assembled Kits (6)
Carrier Wireless (1)
Cable and Misc (14)
Hardware and Mounting (23)
Configuration Library (FREE!) (7)
Quick Find
search products
search articles
New Articles
Case Studies
Product Guides (2)
Mikrotik Configuration (17)
Technical (5)
Community News (9)
Q&A (28)
Product Advisory (7)
Policy and Information (7)
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us
Radio Theory and Link Planning by Mike Everest

Link Planning Calculations for Microwave Wireless

This article is based largely on an original article by Mathias Coinchon and published with the kind permission of the Author.



Power is expressed in Watts or in the Decibel relative units compared to milliwatts (dBm).

Conversion from Watts (W) to decibels "milliwatts" (dBm):

dBm: Watts:

(dBm= 10*log10(P/ 0.001))

For example:

  • EMP8602+s cards have an output power of 600 mW (0.6 W)
  • RB/CRD Corssroads device has power output of 400 mW (0.4 W)

Loss in a coaxial cable at 2.45 GHz

Here are some loss value for common coaxial cables:

  • RG 58 (quite common, used for Ethernet): 1 dB per meter.
  • RG 213 ("big black", quite common): 0.6 dB per meter.
  • RG 174 (thin, seems to be the one used for pigtail adapter cables): 2 dB per meter.
  • LMR-400: 0.22 dB/m per meter.

Choose type of cable:

Length (meter): Loss in dB (negative value !):


  • Antenna gain is normally given in isotropic decibels [dBi]. It's the power gain in comparison to an isotropic antenna (antenna that spread energy in every directions with the same power....theoretical view it doesn't exist in reality!).
  • Some antennas have their gain expressed in [dBd], it's the gain compared to a dipole antenna. IN this case you have to add 2.14 to obtain the corresponding gain in [dBi].
  • The more an antenna has gain the more it is directive (energy sent in a preferred direction).
  • Antenna coming with WLAN kits are generally whithout much gain (2.14 dBi ).
  • Antenna gain is the same for transmit and receive ;-)

Radiated power

Radiated power (power sent by the antenna) can be easily computed (in dBm):

Radiated power [dBm] = Transmitter power [dBm] - cable loss [dB] + antenna gain[dBi]

  • Legal limit for radiated power (EiRP) for 2.4GHz spectrum in Australia is 36dBm (=~ 4 Watts).

Free space loss at 2.45 GHz

It is the power loss of wave travelling in free space (whithout obstacles).

Correspondance between free space gain loss in dB and distance in kilometer (km) :

Loss in dB (negative value !): kilometers:

(Friis formula)

  • These value are only valid for a frequency of 2.45 GHz !

Receiver sensitivity

Receiver has a minimum received power threshold (on the card connector) that the signal must have to achieve a certain bitrate. If the signal power is lower the maximum achievable bitrate will be decreased or performance will decrease. So we have better use receiver with low threshold value, here are some example receiver sensitivity values:

  • Engenius EMP 8602+S 802.11a: 6Mbps => -90dBm, 54Mbps => -74dBm
  • Engenius EMP 8602+S 802.11g: 6Mbps => -92dBm, 54Mbps => -76dBm
  • Engenius EMP 8602+S 802.11g: 11Mbps => -92dBm, 1Mbps => -96dBm
  • RB/CRD (Crossroads) 802.11b: 1Mbps => -97, 11Mbps => -92
  • RB/CRD (Crossroads) 802.11g: 6Mbps => -94, 54Mbps => -74
  • Orinocco cards PCMCIA Silver/Gold : 11Mbps => -82 dBm ; 5.5Mbps => -87 dBm; 2Mbps=> -91 dBm; 1Mbps=> -94 dBm.

    (These are values given by the manufacturer).

Signal to Noise Ratio

Receiver sensitivity is not the only parameter for the receiver, we have also to take into account the signal to noise power ratio. It's the minimum power difference to achieve between the wanted received signal and the noise (thermal noise, industrial noise due for example to microwave ovens, interering noise due to other WLAN on the same frequency band). It is defined as:

Signal/Noise Ratio [dB] = 10 * Log10 (Signal Power [W] / Noise Power [W])

If the signal is more powerful than the noise, signal/noise ratio (also called S/N ratio) will be positive. If the signal is buried in the noise, the ratio will be negative. In order to be able to work at a certain data rate the system needs a minimum S/N ratio:

  • Orinoco PCMCIA Silver/Gold: 11Mbps => 16 dB ; 5.5 Mbps => 11 dB ; 2 Mbps => 7 dB ; 1 Mbps => 4 dB.

If the noise level is very low then the system will be limited more by the receiver sensitivity than by the S/N ratio. If the noise level is high then it will be the Signal/Noise ratio that will count to achieve a given data rate. If the noise level is high we will need more received power. In normal conditions whithout any other WLAN on the frequency and whithout industrial noise the noise level will be around -100dBm. For example to achieve a 11 Mbps data rate with an Orinoco 802.11b card we would need a received power 16dB higher (S/N ratio) so a level of -100+16=-84 dBm but in fact the minimum receiver sensitivity is at -82 dBm...higher than -84. It means in that case the mimimum receiver sensitivity is the limiting factor for the system.

Link budget

Link budget is the computation of the whole transmission chain. Here's a budget for free space loss transmission:

  • Transmit [dBm]: transmitter power [dBm] -cable loss [dB]+ antenna gain [dBi]
  • Propagation [dB]: Free space loss [dB].
  • Receive [dBm]: antenna gain[dBi]- cable loss [dB]- receiver sensitivity [dBm]

Link working condition is that the total : Total Transmit + Total Propagation + Total Receive must be greater than 0 . The remain gives the margin of the system.

NOTE: These rules are theoretical. It represents the maximum achievable for a system. In reality we will have interferences (other WLAN networks, bluetooth), industrial noise (microwave ovens), atmospheric losses (air moisture, scattering, refraction), badly pointed antenna, reflections,... that will affect performances. It is so necessary to take a sufficient security margin (5-6 dB or more on large distances).

Transmit Transmitter output power : dBm
  Cable loss (negative value!) : dB
  Antenna gain : dBi
Propagation Free space loss (negative value!) : dB
Receive Antenna gain : dBi
  Cable loss (negative value!) : dB
  Receiver sensitivity (generally negative value) : dBm
Total Remaining margin: dB
Legal limit  


Propagation: Fresnel ellipsoid

A simple and quick explanation of Fresnel ellipsoid role in radio propagation is to see the thing like a virtual "pipe" where most of the energy travels between a transmitting and receiving site. So in order to avoid losses there should be NO obstacles inside this zone (forbidden region) because an obstacle will disturb "the energy flow". (the explanation is really simplified !).

For example, if half of the forbidden zone is masked (antenna at the limit of line of sight), there will be a signal power loss of 6 dB (power loss of 75 %).

Distance "D" between transmitter and receiver [meters] :

Distance "d" between transmitter and obstacle [meters] :

Radius "R" of forbidden zone at this distance [meters] :

  • These values are only valid for a frequency of 2.45 GHz ! (would you like them for another frequency ?)

(The radius of forbidden region here is 0.6 x Radius of first Fresnel ellipsoid)

Propagation: Diffraction

When an obstacle is located between the transmitter and the receiver some energy still pass through thanks to the diffraction phenomenon on the top edge of the obstacle. The higher the frequency of the transmission the higher the loss will be.


Height "h" between antenna top and obstacle top [meters] :

Distance "D1" between transmitter and obstacle [meters] :

Distance "D2" between receiver and obstacle [meters] :

Power loss at 2.45 Ghz [dB] :

  • These calculation are valid in the case of D1 and D2 far greater than h.
  • This loss is to add to the free space propagation loss.
  • The loss is the same in a transmission in the opposite direction (transmitter replaced by receiver and vice versa).
  • Reference: S. Saunders: Antenna and propagation for wireless communication systems.


Propagation: Polarisation

Wave polarisation is given by the type of your antenna and its orientation (radiating element) respectively to the ground . For a example a whip antenna will give a vertical polarised wave when set vertically ( | ) and horizontal polarisation when lying horizontal (--). The same hold for Yagi antennas ( |-|-|-| ). Helical antennas produce neither vertical nor horizontal polarisation but circular polarisation. Circular polarisation can turn either right or normal cork openers and joke cork openers ;-)

Practically in a transmission system transmitter and receiver antennas should have the same polarisation for best performance. (As polarisation change with diffractions and reflection this rule does not always hold). Vertical polarisation is prefered for long range transmission because the ground effect attenuate the signal power in horizontal polarisation case in long range.

A transmission system with circular polarisation antennas is a good way to attenuate the effect of reflections (principle used for GPS).

Reflections and delay spread

Radio waves reflect ont the obstacles they meet. At the receiver side we catch then at the same time the direct wave (if in line of sight) and the reflected waves. This leads to canceled power at certain frequencies and also a time difference between the different received components that makes the received signal spread in the time domain. Consequence on the system is harmful and lead to decreased performances (transmission errors). In order to reduce this effect the receiver has what we call an equaliser that counteract these faults. Anyway this has a limited capacity and manufacturers give delay spread limit in order to achieve minimum error rate at a certain data rate:

  • Orinoco PCMCIA 802.11b card, delay spread values for a frame error rate (FER) lower than 1%: 11Mbps => 65 ns ; 5.5 Mbps => 225ns ; 2 Mbps => 400ns ; 1Mbps => 500 ns.

We see that for higher bit rate we have better not having to long reflections. The time difference for a reflection can be easily calculated as radio wave travel at the speed of light (300'000'000 m/s):

Time difference [s] = Length difference between direct path and reflected path [m] / 300'000'000

So a time difference of 50 nanoseconds corresponds to a path length difference of 15 meters. In order to minimise the reflection rate it is better using directive antennas, be in line of sight. Another possibility is also to use circular wave polarisation antennas (helical antenna) that cancel quite well the first reflexions.

Reflections also exists in the ensemble coaxial cable-connectors-antennas if these are not well adapted and designed (bad impedance, badly tuned antenna => standing waves, bad SWR) and so may lead to transmission errors.

Warning ! The delay spread value correspond to a computation that involve the level and time difference of every component:
Delay spread [s] = sum on all components of { (component weight) * (component time difference) }

References, documentation

Date Added:
Current Comments: 0
Write Review
Tell a friend
Tell a friend about this article:  
Shopping Cart
0 items
Latest News
about 1 day ago
Cute as a button! The hAP-mini 3 port wifi router from MikroTik has finally passed all relevant certifications! Ge…
more >>
about 10 days ago
LOOK! The new wsAP-lite is a dual band WiFi AP with passthrough PoE ethernet that fits into a power point profile!
more >>
about 10 days ago
The new LtAP-mini is the ideal mobile and vehicle connectivity system with GPS - add your own 4G modem for the ulti…
more >>
about 10 days ago
The cool new RBLHGG-60adkit Wireless Wire Dish Kit is on its way - available for pre-order right now!
more >>
about 11 days ago
DuxTel News: Half-price Mimosa, MikroTik LTE updates, MUM 2018 Highlights -
more >>
about 01 month ago
CCR1072-1G-8S+ - it doesn't get any better than this! Normally $4325, special price $2999 - (ex demo model, 1 unit…
more >>
about 01 month ago
ready for MikroTik Certified Training - kicking off TOMORROW! :)
more >>
about 01 month ago
MikroTik's first ever true 802.3af/at PoE switch with auto-detecting 24v/48v and 4x 10GB SFP+ uplink is available n…
more >>
about 01 month ago
Thinking about horns? See here! :)
more >>
Follow our tweets for all the latest news and updates!
RB953GS-5HnT: 5 wired, 3 wireless with 3x3 MIMO 11n & 2 miniPC-e
Only MikroTik routerBOARD device at the moment which support ..
5 of 5 Stars!

Copyright © 2018 DuxTel Online Store